Stand off installation system TherMax II

Varijante proizvoda

8 Varijanta(e) proizvoda

Threaded rod

Thread

Total length

Max. thickness of non-bearing layer

Installation torque

Pregledano 8 od 8 varijanti

Advantages

The anti-cold cone made of glass fibre reinforced plastic interrupts the thermal bridge between the fixture and the anchor in the masonry.
The optimized geometry of the cone enables easy and precise cutting into the ETICS. This makes installation particularly easy and at the same time prevents damage to the insulation material and plaster.
Thanks to the articulated connection between the anti-cold cone and the cover cap, angled drill holes of up to 5° can be compensated for.
The elastic EPDM sealing ring is placed on the anti-cold cone at the end of installation. This ensures that the seal is not damaged by the plaster during installation and guarantees 100% functionality and resistance to driving rain. Additional sealing of the annular gap with an elastic sealant and adhesive is not necessary.
With just one TherMax II, insulation thicknesses of 60 to 300 mm in concrete and up to 250 mm in perforated building materials can be covered. The threaded rod is shortened to the appropriate insulation thickness at the installation site.
The stand-off installation system is approved in combination with a wide variety of injection mortars for high loads in a wide range of building materials.
The anti-cold cone and threaded pin can be adjusted retrospectively without expensive special tools to ensure precise alignment. This offers maximum flexibility and is also covered by the approval.
The parts of TherMax II that lie outside the insulation are made of stainless steel.

Applications

For the thermally separated fixing of:

Awnings
Canopies
French balcony railings
Air conditioning units
Satellite dishes

Building materials

Approved for:

Concrete, cracked and non-cracked
Vertically perforated brick
Hollow blocks made from lightweight concrete
Perforated sand-lime brick
Solid sand-lime brick
Solid brick
Aerated concrete

Detaljne informacije o građevinskom materijalu možete pronaći u dokumentu za registraciju.

Odobrenja

2025-01-0118-K1

Functionality

The TherMax II is suitable for pre-positioned installation.
The self-tapping, glass fibre reinforced cone cuts its own way through the plaster into the insulation during installation.
The anti-cold cone uses a thermal barrier to minimise heat losses.
In the case of a resistant plaster (e.g. thick cement plaster), it is recommended to us the included TherMax II cutting blade for grinding out the plaster.
Inclined drill holes up to 5° are levelled by the separated cover cap with sealing ring in combination with the rounded head of the anti-cold cone.
The elastic EPDM sealing ring is placed loosely on the cover cap and thus provides permanent protection against moisture and driving rain.
The anti-cold cone and the threaded pin can be subsequently adjusted.

Mounting Strip 1 Picture

1 / 11

Test Certificate

pdf, 2025-01-0118-K1

PfB - Short report fischer TherMax II

Napravljeno 28. 01. 2026.

Load Table

pdf,

Stand-off installation TherMax II 12 and 16 with load-bearing anchor rod made of zinc-plated steel and a displacement of 3 mm

Load Table

pdf,

Stand-off installation TherMax II 12 and 16 with load-bearing anchor rod made of stainless steel R-70 and a displacement of 5 mm

Technical Data Sheet

pdf,

Installation data TherMax II M12/M16

Installation Instructions

pdf,

TherMax II

Marketing Documents

pdf,

Thermal separation with secure hold.

Threaded rod ( ø x length )	M12 x 204 mm
Thread ( M )	M12
Thread ( A )	M12
Total length ( l )	240 mm
Max. thickness of non-bearing layer ( e )	64 - 170 mm
Installation torque ( T_inst )	20 Nm
Contents	20 x TherMax II M12 x 240 20 x Sleeve 20 x 130 5 x Bit 5 x Cutting blade 5 x Manual
Packaging	Folding box
Amount	20 pcs
GTIN (EAN-Code)	4048962541595

Threaded rod ( ø x length )	M12 x 204 mm
Thread ( M )	M12
Thread ( A )	M12
Total length ( l )	240 mm
Max. thickness of non-bearing layer ( e )	64 - 170 mm
Installation torque ( T_inst )	20 Nm
Contents	2 x TherMax II M12 x 240 2 x Sleeve 20 x 130 1 x Bit 1 x Cutting blade 1 x Manual
Packaging	Folding box
Amount	2 pcs
GTIN (EAN-Code)	4048962541601

Threaded rod ( ø x length )	M16 x 264 mm
Thread ( M )	M16
Thread ( A )	M12
Total length ( l )	300 mm
Max. thickness of non-bearing layer ( e )	64 - 220 mm
Installation torque ( T_inst )	20 Nm
Contents	20 x TherMax II M16 x 300 20 x Sleeve 20 x 130 5 x Bit 5 x Cutting blade 5 x Extension hose for static mixer 5 x Manual
Packaging	Folding box
Amount	20 pcs
GTIN (EAN-Code)	4048962541649

Threaded rod ( ø x length )	M16 x 344 mm
Thread ( M )	M16
Thread ( A )	M12
Total length ( l )	380 mm
Max. thickness of non-bearing layer ( e )	64 - 300 mm
Installation torque ( T_inst )	20 Nm
Contents	20 x TherMax II M16 x 380 20 x Sleeve 20 x 130 5 x Bit 5 x Cutting blade 5 x Extension hose for static mixer 5 x Manual
Packaging	Folding box
Amount	20 pcs
GTIN (EAN-Code)	4048962541656

Threaded rod ( ø x length )	M16 x 344 mm
Thread ( M )	M16
Thread ( A )	M12
Total length ( l )	380 mm
Max. thickness of non-bearing layer ( e )	64 - 300 mm
Installation torque ( T_inst )	20 Nm
Contents	2 x TherMax II M16 x 380 2 x Sleeve 20 x 130 1 x Bit 1 x Cutting blade 1 x Extension hose for static mixer 1 x Manual
Packaging	Folding box
Amount	2 pcs
GTIN (EAN-Code)	4048962541663

Stand off installation system TherMax II

Varijante proizvoda

Prednosti / Opis proizvoda

Prijava i odobrenje

Uputstvo za montažu

Dokumenti za preuzimanje